-- Parameters
local outletValve = 2 -- vent to outlet valve, FIO number
local inletValve = 0 -- pressurize system valve, FIO number
local pressureTransducer = 0 -- Pressure transducer AIN number
LJ.IntervalConfig(0, 1000) -- Control loop period in ms

-- Local variables for speed
local checkInterval = LJ.CheckInterval
local mbR = MB.R
local mbW = MB.W
local RPM = 400
local maxRPM = 1000
local desiredPumpPSI = 120
local currentPumpPSI = 0

mbW(46000, 3, 0) -- clear user RAM
mbW(46180, 0, 14) -- reset setpoint
mbW(48005, 0, 1) --ensure analog system is powered on

--SPI Params
mbW(5000, 0, 4)  --CS (FIO4)
mbW(5001, 0, 5)  --CLK (FIO5)
mbW(5002, 0, 6)  --MISO (FIO6)
mbW(5003, 0, 7)  --MOSI (FIO7)
mbW(5004, 0, 1)  --Mode
mbW(5005, 0, 0)  --Speed
mbW(5006, 0, 0)  --Options, disable CS
mbW(5009, 0, 1)  --Num Bytes to Tx/Rx

print("Initialized")

--Step 1: Ensure 4-thruster equivalent flow restriction is installed
--Step 2: Load and Prime the system with one of the viscosity analog fluids
--Step 3: Open Inlet and Outlet Valves.

--LJ.DIO_S_W(outletValve,0) -- Changes outlet valve to output low 
--LJ.DIO_D_W(outletValve,1) -- Turn on output valve
--
--LJ.DIO_S_W(inletValve,0)  -- Changes inlet valve to output low 
--LJ.DIO_D_W(inletValve,1)  -- Turn on inlet valve
  
--Step 4: Sweep from 500 ROM to max motor power, accelerating at 100RPM/sec.

while true do
  if LJ.CheckInterval(0) then
    if RPM < maxRPM then
      RPM = RPM + 100
      print ("RPM is : ", RPM)
    else 
      print("Max RPM")
      break end
  end
end

--Step 5: Control Output Pressure to flight level and run pump until steady state temp is reached.

local testData = {{0x01}}
local dataSelect = 1-- 1 or 2 for each dataset, change this for different data sets

LJ.IntervalConfig(0, 100) --Configure Interval, in millis
local checkInterval=LJ.CheckInterval
while true do
  if checkInterval(0) then
    local pressure = mbR(pressureTransducer * 2, 3) * 29.6209 - 50 -- Read AIN0, convert to PSIA
    print(pressure)
    local testLen = table.getn(testData[dataSelect])
    MB.W(5009, 0, testLen)--load the number of bytes
    MB.WA(5010, 99, testLen, testData[dataSelect])--load data into DATA_TX
    MB.W(5007, 0, 1)--SPI_GO
    local rxData = MB.RA(5050, 99, testLen)--read data from DATA_RX
    
    --Compare the data
    local pass = 1
    for i=1,testLen do
      print(testData[dataSelect][i])
      if(testData[dataSelect][i] ~= rxData[i]) then
        print(string.format("0x%x (tx) does not match 0x%x (rx)", testData[dataSelect][i], rxData[i]))--Show data recieved
        pass = 0
      end
    end
    if(pass == 1) then
      print("Data recieved")
    else
      print("----")
    end
  end
end
--Step 6: Repeat with other propellant viscosity analog fluid.